The belt should slip right into place. If it seems to be too tight or difficult to set in place, it may be necessary to adjust the motor mount to provide more slack. Then you can re-tighten the tension once the belt is in place. Check the manufacturer’s specifications for proper tension—in most cases, the belt should deflect about an inch when you press down on it.
Engineers have pointed out some areas where efficiency of the existing hardware could be improved. For example, the fan blades used to move the air are usually stamped from sheet metal, an economical method of manufacture, but as a result they are not aerodynamically efficient. A well-designed blade could reduce electrical power required to move the air by a third.[26]
If your home is not heated using forced air, chances are a boiler will make sure you stay warm during cold nights. A hot water system delivers hot water through a network of pipes that run to every room in your house. The heating effect gets maximized through radiators. The most common issues with hot water heating tend to be not be major, but small problems that add up over time. Mineral deposits within the water tank, a pilot light malfunction, or an issue with a radiator itself can require professional repair. On average, you will pay between $183 and $582 for these problems. The exact amount will depend on the exact problem, as described in our boiler repair cost guide.
As your trusted HVAC service experts since 1960, Miller's Air Conditioning & Heating was established before Livermore became an official city.  We have a long-term commitment to the local community and have built solid relationships across generations of families.  Family owned and operated, we recognize the importance of an HVAC provider you can always depend on to serve your best interests.  At Miller's Air Conditioning & Heating we uphold exacting standards of quality, from the products we recommend and install, to the integrity of workmanship.  By refusing to settle, we provide a greater return from all of our services, including new system installation, replacement, seasonal maintenance, and repair of air conditioners, heat pumps, furnaces, ductless units, and attic fans.  Whether you’re a first-time homeowner or dissatisfied with the contractors you’ve tried in the past, we’ll make sure Miller's Air Conditioning & Heating satisfies your every expectation.

It can be difficult to find the right company to do Aurora furnace repair and Aurora furnace replacement. When looking for the right help choose an Aurora furnace replacement and repair company that comes recommended and has a strong reputation. As a licensed furnace replacement company in Denver, Brothers Plumbing Heating and Electric has been working on the repair and replacement of furnaces for many years. Furthermore, we have a long list of happy customers that recommend us to all their friends and family.

The thermocouple is a copper rod that the pilot flame heats-up. When it gets hot enough, the thermocouple signals that there is enough heat to burn the gas fuel being released into the appliance—and so it allows the gas to be released to the burners. In some cases where the pilot light won’t stay lit, the thermocouple needs to be adjusted or replaced. This is generally a job for a professional.
In Denver, when it comes to fast, reliable and high quality AC repair, we here at Brothers Plumbing Heating And Electric are the company to call. Our Denver AC repair and replacement technicians are always standing by to give you a helping hand with any and all of your air conditioning problems. We are the go-to company when it comes to AC repair in Denver. Give us a call today. Click here to learn more about our cooling services today.
ISO 16813:2006 is one of the ISO building environment standards.[29] It establishes the general principles of building environment design. It takes into account the need to provide a healthy indoor environment for the occupants as well as the need to protect the environment for future generations and promote collaboration among the various parties involved in building environmental design for sustainability. ISO16813 is applicable to new construction and the retrofit of existing buildings.[30]

Sometimes a heating and air conditioning system just needs to be repaired rather than completely replaced. You may need air conditioning repair services if there is leaking around the outside unit, the air coming into the house isn't hot or cool enough, the unit is short-cycling or constantly turning on and off, using the system is consistently resulting in higher-than-normal energy bills, or if there is excessive noise during startup and operation.

Ductwork pinging or popping. If you hear a pinging or popping sound coming from metal ductwork, this may be caused by thermal expansion or by air blowing past a loose flap of metal. Track along the duct runs, listening for the sound. If you find it, make a small dent in the sheet metal to provide a more rigid surface that’s less likely to move as it heats and cools.
When you work with Bob’s, we make sure your furnace is properly sized and installed for optimal performance. When it comes to furnace installation in Renton, WA, Bob’s is dedicated to excellence, which defines our service. We know that professional furnace installation is the best way to protect its performance quality. Call today for more details.

Our factory trained and regularly trained specialists arrive right on time, dressed in uniform, prepared for the job, and respect your property.  When you call on Efficient Comfort, we answer with local, good people doing great work.  Contact us at (720) 627-6391 for prompt, expert, and affordable comfort solutions throughout Boulder, CO, Westminster, CO, Broomfield, CO, Golden, CO & Louisville, CO.

If your thermostat has a small lever that moves along a calibrated scale that indicates “longer” (not the heat temperature lever), you can try adjusting this—the heat anticipator. Just set it one calibration mark closer to the “longer” setting if the furnace goes off and on too frequently or one mark away if the furnace allows room temperature to rise too high or drop too low before going on or off. It may take several hours for the thermostat to stabilize at this setting, so wait a while and then adjust it again if necessary.


The heat-exchanger cools the air that is being forced through it by the furnace blower. As the warm air comes in contact with this cool surface the water in the air condenses. By pulling the water molecules from the air. According to the psychometric chart[42] as relative humidity decreases in order to feel cool you will have to lower the temperature even more. A common way to counteract this effect is by installing a whole-home humidifier.[43] Similarly, installing a high efficient system this need to turn the temperature down wont have such and influence on your energy costs.
Air Conditioning Your home's air conditioner is an essential part of your overall indoor comfort. A properly working system can mean the difference between a cool, comfortable summer and a hot, miserable few months. If you're currently dealing with a broken air conditioner, an inefficient system, or you would like to schedule a routine, pre-season tune-up, Horizon Services is here to help!
×