Finally, don't underestimate the thermostat as a potential reason why your furnace is not working. Everything on the heating unit itself may function perfectly, but your home still will not heat right if the console you use to set the temperature doesn't communicate your input. A faulty thermostat can either be due to the wall unit itself, or the wiring that connects it to your furnace. Average thermostat repair costs are between $108 and $282, including labor. Replacement costs, of course, depend on the thermostat you choose. Visit our thermostat repair cost guide to learn more about this type of issue.
If you believe that the ac not working or you’re getting little or no cold air, check these three things first. Make sure all the registers in the house are wide open. Then be sure the furnace filter is clean. Then go outside and clean off the condenser coils (Photo 2). If several registers were closed or the filter was clogged, the reduced airflow could have caused the evaporator coil to ice up and stop cooling your home. If you’ve changed the filter and opened all the registers and you’re still not getting airflow at the registers, deice the A-coil. Move the thermostat mode switch from “Cooling” to “Off” and move the fan switch from “Auto” to “On.” Let the blower run for at least 30 minutes or until there’s good airflow at the registers. Then turn the AC back on to test it. If it works for the next 12 hours, you’ve solved the problem.
Our technicians explain all of your options before beginning the repair, so you can decide whether a repair or replacement is best for you. Our No Surprises Pricing—including charging by the job, not by the hour—means the price we quote you is the price you pay. If you decide that replacing your furnace is the best course of action, we can install a new, high-efficiency model in its place.
Berkeys knows how unbearable the Dallas, Plano, Fort Worth and Arlington Texas summers can be. Assuring your home’s air conditioning system is functioning properly is our job! We’ll always have the solution to your air conditioning problem, and we’ll rescue you when your system stops working. Call us or schedule your service online today and we think you will see why we are considered to be one of the Best A/C Companies in the Dallas & Fort Worth area!
Given the broad price ranges above, it's easy to recognize that the cost of your furnace repair varies drastically based on which parts need attention. As a result, it makes sense to gain a better understanding of the parts that heat your home, and how much they cost to repair. Repairing or replacing your furnace’s blower motor can cost you anywhere between $150 and $450, depending on the extent of the damage. Heat exchanger repair costs can vary greatly, from as little as $100 for a simple fix to as much as $1,200 for a full replacement. Repairing a furnace igniter will only cost you $300 at most, while flame sensor repairs generally fall between $80 to $250. The average cost to repair your Thermostat will range from $108 to $282.
If your furnace has a pilot light, look for the flame. Check your owner’s manual or the instructions posted inside the furnace cabinet for step-by-step lighting instructions. Usually this involves first turning the gas valve to Off and waiting a couple of minutes. Then you turn it to Pilot. Next, press and hold it down while you light the flame. Last, wait a minute or so, release it, and then turn it to On.
Berkeys is a licensed HVAC contractor and air conditioning company offering AC repair, Air Conditioning tune-up, and air conditioning replacement services in Southlake, TX, Keller, TX, Coppell, TX, Colleyville, TX, Grapevine, TX, Plano, TX, Fort Worth, TX, Arlington, TX, Frisco, TX, Dallas, TX, Addison, TX, Flower Mound, TX, Irving, TX, McKinney, TX, Arlington, TX, Euless, TX, Denton, TX, Highland Village, TX, Grand Prairie, TX, Westlake, TX, Farmers Branch, TX, Lewisville, TX and more. Call to confirm service for your home.
The contactor (relay) and start/run capacitor(s) (see illustration below) fail most often and are inexpensive. So it’s a safe bet to buy and install those parts right away, especially if your air conditioning service unit is older than five years. The condenser fan motor can also fail, but it runs about $150 — hold off buying that unless you’re sure that’s the culprit.
If you hear clicking that is followed by a hum or buzz, you’re probably hearing the fan motor attempting to start without the boost it needs from the capacitor. You can almost always conclude that the capacitor has failed. Sometimes you can get the compressor fan spinning (clockwise) by pushing it with a thin stick or long screwdriver poked through the grille. But the chances are good that this might work for one cycle, but the capacitor will fail next time the AC goes on. It’s best to replace the capacitor.
When you change the temperature on your thermostat, or the temperature in your home drops, a signal lets the furnace's igniter know that it's time to turn on. Igniters exist in both hot water boilers and forced air furnaces, replacing pilot lights as the switch your unit needs to kick on. Naturally, this is a core part in making sure it works reliably. When it stops working, your unit will not longer know when to actually heat your home. Fortunately, furnace igniter repair doesn't tend to be a major budget problem, and costs less than $300 on average.
At Comfort Plus Services, we set ourselves apart from the rest through quality customer service across Salisbury, MD and surrounding areas. See our Areas of Service. Our strength is in our high standards of job performance and fully trained professionals. Our team upholds a proven reputation and is continually motivated to achieve excellence in every service we provide.
©2018 By Horizon Services, LLC. All Rights Reserved. DE License # PL0000726, HL0000299. Contractor Reg. # PA017876, PA057742. NJ Plumbing Lic. # PL36BI01232300 - David Geiger HIC reg. # 13VH05117300, NJ Master HVACR contractor Lic. # 19HC00193700. MD Master HVACR contractor Lic. # 47186, MD Master Plumber/Gas Fitter Lic. # 63739 – David Geiger. EL.LIC./B.P. #34EI01207700.
The first air conditioners and refrigerators employed toxic or flammable gases, such as ammonia, methyl chloride, or propane, that could result in fatal accidents when they leaked. Thomas Midgley, Jr. created the first non-flammable, non-toxic chlorofluorocarbon gas, Freon, in 1928. The name is a trademark name owned by DuPont for any chlorofluorocarbon (CFC), hydrochlorofluorocarbon (HCFC), or hydrofluorocarbon (HFC) refrigerant. The refrigerant names include a number indicating the molecular composition (e.g., R-11, R-12, R-22, R-134A). The blend most used in direct-expansion home and building comfort cooling is an HCFC known as chlorodifluoromethane (R-22).
When’s the last time you had your home’s heating system maintained? If you’re like most homeowners it’s probably been a while, but keeping your plumbing, heating, and cooling systems under control is vital. That’s where Anthony Plumbing, Heating and Cooling comes in. We’re the best in HVAC Service in Kansas City, MO when it comes to keeping your systems running and your family comfortable. Our company was founded in 1951 and we’ve been providing quality services in Kansas City ever since.We service and do repairs in the following: Kansas City KS Furnace Repair Air Conditioning, Plumbing