Our partner, Goodman Air Conditioning and Heating, is a leading HVAC manufacturer. Their products deliver outstanding comfort with the money-saving efficiency ratings that every homeowner deserves. From the first HVAC diagnostic and inspection to every maintenance test, we ensure that our systems are durable and provide lasting quality to your day-to-day life.
Most modern air-conditioning systems feature a dehumidification cycle during which the compressor runs while the fan is slowed as much as possible[citation needed] to reduce the evaporator temperature and therefore condense more water. When the temperature falls below a threshold, both the fan and compressor are shut off to mitigate further temperature drops;[clarification needed] this prevents moisture on the evaporator from being blown back into the room.[citation needed] When the temperature rises again,[clarification needed] the compressor restarts and the fan returns to low speed.
If your furnace has a pilot light, look for the flame. Check your owner’s manual or the instructions posted inside the furnace cabinet for step-by-step lighting instructions. Usually this involves first turning the gas valve to Off and waiting a couple of minutes. Then you turn it to Pilot. Next, press and hold it down while you light the flame. Last, wait a minute or so, release it, and then turn it to On.
Although HVAC is executed in individual buildings or other enclosed spaces (like NORAD's underground headquarters), the equipment involved is in some cases an extension of a larger district heating (DH) or district cooling (DC) network, or a combined DHC network. In such cases, the operating and maintenance aspects are simplified and metering becomes necessary to bill for the energy that is consumed, and in some cases energy that is returned to the larger system. For example, at a given time one building may be utilizing chilled water for air conditioning and the warm water it returns may be used in another building for heating, or for the overall heating-portion of the DHC network (likely with energy added to boost the temperature).[4][5][6]

Beware these aluminum clad wood doors. The wood is particle board. Why would anyone make a storm door out of particle board? They don't seal it in any way, it gets wet between the aluminum cladding and boils and blisters the aluminum and looks terrible in just a few years. I have two Larson's and they were horrible doors almost from the start. I've seen reviews and EMCO is the exact same way. When your storm door needs a storm door, you bought the wrong door.
Mountain Valley Home Comfort provides expert heating and cooling services in Virginia’s Shenandoah Valley.  Our team of licensed, trained, and experienced professionals handle new installation, retrofit projects, seasonal maintenance and challenging repairs.  When you call on Mountain Valley Home Comfort at (540) 740-3844, we target sustainable solutions to temperature control, saving you time and money, and protecting comfort and budget. Personalizing our services to meet your needs, we ensure the right answer to any requirement.  With organized job sites, swift response, and quick turnaround, our professionals resolve any difficulty and take the best possible care of your essential HVAC equipment.
Before opening the electrical cover on the A/C unit, be sure to shut off all power to the compressor unit and the indoor furnace or air handler, and verify that it is off. Note that this may mean shutting off a circuit breaker that serves the furnace and air handler, and then, near the compressor, pulling out the disconnect block (or shutting off the 220-volt power) to the outdoor compressor.
Circulating refrigerant vapor enters the compressor, where its pressure and temperature are increased. The hot, compressed refrigerant vapor is now at a temperature and pressure at which it can be condensed and is routed through a condenser. Here it is cooled by air flowing across the condenser coils and condensed into a liquid. Thus, the circulating refrigerant removes heat from the system and the heat is carried away by the air. The removal of this heat can be greatly augmented by pouring water over the condenser coils, making it much cooler when it hits the expansion valve.
If you want to avoid major renovations, have a space without the necessary ductwork, or simply want a cost-efficient, simple alternative to cumbersome heating and cooling units, consider a ductless HVAC system from Wm. Price Heating & Cooling! Innovative ductless systems are great for home additions, new construction, condominiums, apartments, or to target temperature control in certain rooms. You’ll have the ability to adjust temperatures for specific zones of the home while also enjoying a non-invasive unit. Ductless HVAC systems are more environmentally responsible, quicker to install, and less wasteful than systems that use ductwork. Get in touch with our team today to learn more about our ductless HVAC services!
Turn off the gas supply valve, typically located by your gas meter on the gas inlet pipe. Turn off the gas by rotating the valve one quarter turn with an adjustable wrench. When the gas is off,  the valve’s oblong stem points perpendicular to the inlet pipe. Then call your gas utility or the fire department from a remote location. Do not return to your home until you know it is safe.
In 1902, the first modern electrical air conditioning unit was invented by Willis Carrier in Buffalo, New York.[citation needed] After graduating from Cornell University, Carrier found a job at the Buffalo Forge Company. There, he began experimenting with air conditioning as a way to solve an application problem for the Sackett-Wilhelms Lithographing and Publishing Company in Brooklyn, New York. The first air conditioner, designed and built in Buffalo by Carrier, began working on 17 July 1902.[citation needed]
An important component of natural ventilation is air change rate or air changes per hour: the hourly rate of ventilation divided by the volume of the space. For example, six air changes per hour means an amount of new air, equal to the volume of the space, is added every ten minutes. For human comfort, a minimum of four air changes per hour is typical, though warehouses might have only two. Too high of an air change rate may be uncomfortable, akin to a wind tunnel which have thousands of changes per hour. The highest air change rates are for crowded spaces, bars, night clubs, commercial kitchens at around 30 to 50 air changes per hour.[17]
AC air handler buzzing sounds. Do you hear a buzzing sound when you turn on the thermostat? The only thing that comes on in the house when you turn on the thermostat is the fan relay and fan in the air handler or furnace. Try switching the thermostat HEAT/COOL switch to OFF. Then switch the fan switch from AUTO to ON. The fan (only) should come on. If the air handler makes a buzzing sound, it probably has a bad fan relay or, more likely, blower fan.
Advantages of the ductless system include smaller size and flexibility for zoning or heating and cooling individual rooms. The inside wall space required is significantly reduced. Also, the compressor and heat exchanger can be located farther away from the inside space, rather than merely on the other side of the same unit as in a PTAC or window air conditioner. Flexible exterior hoses lead from the outside unit to the interior one(s); these are often enclosed with metal to look like common drainpipes from the roof. In addition, ductless systems offer higher efficiency, reaching above 30 SEER.[39]

Let Fayette Furnace help you step up your home efficiency with a wide range of air conditioning and heating products, services and our skilled team of technicians. An employee owned company since 1920; we pride ourselves on continuing a longstanding tradition of honesty, professionalism and expertise. Call and ask about our service maintenance agreements to save money on maintenance and emergency calls. A yearly service is recommended per the manufacturer’s warranty on the equipment.
Ductwork pinging or popping. If you hear a pinging or popping sound coming from metal ductwork, this may be caused by thermal expansion or by air blowing past a loose flap of metal. Track along the duct runs, listening for the sound. If you find it, make a small dent in the sheet metal to provide a more rigid surface that’s less likely to move as it heats and cools.

The heat-exchanger cools the air that is being forced through it by the furnace blower. As the warm air comes in contact with this cool surface the water in the air condenses. By pulling the water molecules from the air. According to the psychometric chart[42] as relative humidity decreases in order to feel cool you will have to lower the temperature even more. A common way to counteract this effect is by installing a whole-home humidifier.[43] Similarly, installing a high efficient system this need to turn the temperature down wont have such and influence on your energy costs.
If your thermostat has a small lever that moves along a calibrated scale that indicates “longer” (not the heat temperature lever), you can try adjusting this—the heat anticipator. Just set it one calibration mark closer to the “longer” setting if the furnace goes off and on too frequently or one mark away if the furnace allows room temperature to rise too high or drop too low before going on or off. It may take several hours for the thermostat to stabilize at this setting, so wait a while and then adjust it again if necessary.

This is probably the most common question we hear. To give an accurate price, we need to get a safety certified technician out to your home in a fully stocked truck to take a look at your particular situation. Our technician will give you a precise price with your options BEFORE any work begins. Each of our technicians are well trained, experienced, drug tested and background checked so that you can rest easy knowing your services will be performed in a timely and professional manner. If you need help paying for your services, we even offer financing with approved credit through Wells Fargo. Click here to learn more about our financing services.
Though forced-air furnaces are normally quite reliable, they can break down. To avoid break downs, it pays to know how to take care of your furnace and fix it when something goes wrong. Inevitably, a furnace stops working when you need it most. Consequently, fixing becomes urgent very quickly. The following instructions will help. With a little do-it-yourself experience and the proper guidance, you can troubleshoot and repair a variety of furnace problems yourself.
If your furnace’s motor runs but the blower doesn’t move air, the belt that connects the two probably has broken. Replacing it is an easy fix. First, turn off all power to the unit and turn off the gas at the gas valve that serves the furnace. Remove the door on the front of the furnace cabinet to give you access to the blower (it might be on a slide-out drawer.) Check the number stamped on the belt and get an exact replacement from a home center or heating supply outlet.
Locally owned and operated, our entire Dayton staff is ready to assist you the moment you call. You can expect the same service from the nearly 300 other One Hour Heating and Air Conditioning shops across the country. Being part of an organization as large as One Hour gives us leverage and backing with all the major brands such as Trane, Carrier, Lennox, Bryant, Honeywell, Goodman and Amana…and many more.  Being part of the One Hour Family allows us to stock our trucks like rolling warehouses carrying a large amount of parts and equipment so you don’t have to wait.  We also provide full service duct cleaning for you home or office.  Our professional staff will give you a free in home estimate and thoroughly explain the Duct Cleaning process.
We live in a recently completed townhouse that was built with double-wall construction. That construction method was touted by the builder as what would keep sound from penetrating between the units. But we can hear the next door neighbors' TV and stereo, and sometimes voices and even snoring, through the wall. While sometimes it's the volume, mostly it's the bass sounds coming through the wall. They say they don't hear us, but we keep our bass turned down. They crank up the bass, and they are not going to change that. They also are not going to do anything construction-wise to help from their side. What is the best way for us to try to block the low frequency/bass sounds from penetrating the existing wall into our side?

Cleaning the debris that builds up on your filters will aid with the flow of air. When your air filter is clogged, your air handler must work harder to compensate for the blockage of air flow. In addition to driving up your utility bill, the reduced air flow through your heating and cooling system can cause your heat exchanger to overheat and shut off too quickly.    
×