If your furnace’s motor runs but the blower doesn’t move air, the belt that connects the two probably has broken. Replacing it is an easy fix. First, turn off all power to the unit and turn off the gas at the gas valve that serves the furnace. Remove the door on the front of the furnace cabinet to give you access to the blower (it might be on a slide-out drawer.) Check the number stamped on the belt and get an exact replacement from a home center or heating supply outlet.
what should be the length of the drain vent. I had it at the roof level. But since I am getting bad smell in my house via bathrooms (or may be via roof door), I have just extended the length of the vent pipe. Is there any scientific method to estimate the right length? Plus is there any tester to test from where the bad sewage odor is coming from into the living room. It's a two-story villa.
Finally, don't underestimate the thermostat as a potential reason why your furnace is not working. Everything on the heating unit itself may function perfectly, but your home still will not heat right if the console you use to set the temperature doesn't communicate your input. A faulty thermostat can either be due to the wall unit itself, or the wiring that connects it to your furnace. Average thermostat repair costs are between $108 and $282, including labor. Replacement costs, of course, depend on the thermostat you choose. Visit our thermostat repair cost guide to learn more about this type of issue.
"I purchased a mobile home recently and the electrical was a mess. One of the circuits was down and the previous owner had wired the breaker box very strange. One outlet (on a working circuit) had an electrical fire that destroyed it. I'm a DIY guy but I haven't done much with electric before so I asked for a quote on this website. Todd called me within the hour, and we set an appointment for 2 days later. He was on time to the appointment and was able to diagnose the problem AND fix my destroyed outlet within 10 minutes (I already had a new outlet ready to be installed). What's more, he didn't even charge me for it, just said that when I was ready to fix my circuit to give him a call (I'm redoing all the plumbing right now). Todd deserves 6 stars. He is an expert at what he does, he's friendly, he's reasonable, and he's fast. Don't hesitate to contact him. I wish more technical professionals were like him."
The Chartered Institution of Building Services Engineers is a body that covers the essential Service (systems architecture) that allow buildings to operate. It includes the electrotechnical, heating, ventilating, air conditioning, refrigeration and plumbing industries. To train as a building services engineer, the academic requirements are GCSEs (A-C) / Standard Grades (1-3) in Maths and Science, which are important in measurements, planning and theory. Employers will often want a degree in a branch of engineering, such as building environment engineering, electrical engineering or mechanical engineering. To become a full member of CIBSE, and so also to be registered by the Engineering Council UK as a chartered engineer, engineers must also attain an Honours Degree and a master's degree in a relevant engineering subject.
Some systems include an "economizer mode", which is sometimes called a "free-cooling mode". When economizing, the control system will open (fully or partially) the outside air damper and close (fully or partially) the return air damper. This will cause fresh, outside air to be supplied to the system. When the outside air is cooler than the demanded cool air, this will allow the demand to be met without using the mechanical supply of cooling (typically chilled water or a direct expansion "DX" unit), thus saving energy. The control system can compare the temperature of the outside air vs. return air, or it can compare the enthalpy of the air, as is frequently done in climates where humidity is more of an issue. In both cases, the outside air must be less energetic than the return air for the system to enter the economizer mode.
In 1820, English scientist and inventor Michael Faraday discovered that compressing and liquefying ammonia could chill air when the liquefied ammonia was allowed to evaporate. In 1842, Florida physician John Gorrie used compressor technology to create ice, which he used to cool air for his patients in his hospital in Apalachicola, Florida. He hoped to eventually use his ice-making machine to regulate the temperature of buildings. He even envisioned centralized air conditioning that could cool entire cities. Though his prototype leaked and performed irregularly, Gorrie was granted a patent in 1851 for his ice-making machine. Though his process improved the artificial production of ice, his hopes for its success vanished soon afterwards when his chief financial backer died and Gorrie did not get the money he needed to develop the machine. According to his biographer, Vivian M. Sherlock, he blamed the "Ice King", Frederic Tudor, for his failure, suspecting that Tudor had launched a smear campaign against his invention. Dr. Gorrie died impoverished in 1855, and the dream of commonplace air conditioning went away for 50 years.
As a Kansas City Heating and Cooling company, Anthony’s professional technicians are not only friendly, but extremely skilled. No matter what the problem with your air conditioner or furnace is, they can solve it. But don’t wait until there is a problem. Enroll in our annual service program and we’ll keep all your equipment maintained so you get the most out of your furnace, air conditioner, and plumbing equipment. An ounce of prevention is worth a pound of cure, so our service program pays for itself.