Online reviews and family recommendations led me to Extreme's One Hour Heating & Air Conditioning services. I'm very grateful that they did! The technician, Michael T., was outstanding. He was friendly, very knowledgeable, and explained everything in a manner in which I could understand. He was super-prompt, he did only what truly needed done, and explained ways for me to better maintain my own AC unit. He also suggested I consider having my units serviced from time to time due to their age, but recommended I wait until there was a special going on. He also was very friendly with my incredibly hyper dog, who was very happy to jump all over him. To me, that all speaks to top-notch service. I know now that the only call I need to make if I'm having trouble with heating & air is to Extreme's One Hour Heating & Air Conditioning. Thanks again, Michael!


SEER is related to the coefficient of performance (COP) commonly used in thermodynamics and also to the Energy Efficiency Ratio (EER). The EER is the efficiency rating for the equipment at a particular pair of external and internal temperatures, while SEER is calculated over a whole range of external temperatures (i.e., the temperature distribution for the geographical location of the SEER test). SEER is unusual in that it is composed of an Imperial unit divided by an SI unit. The COP is a ratio with the same metric units of energy (joules) in both the numerator and denominator. They cancel out, leaving a dimensionless quantity. Formulas for the approximate conversion between SEER and EER or COP are available.[34]
Some systems include an "economizer mode", which is sometimes called a "free-cooling mode". When economizing, the control system will open (fully or partially) the outside air damper and close (fully or partially) the return air damper. This will cause fresh, outside air to be supplied to the system. When the outside air is cooler than the demanded cool air, this will allow the demand to be met without using the mechanical supply of cooling (typically chilled water or a direct expansion "DX" unit), thus saving energy. The control system can compare the temperature of the outside air vs. return air, or it can compare the enthalpy of the air, as is frequently done in climates where humidity is more of an issue. In both cases, the outside air must be less energetic than the return air for the system to enter the economizer mode.

At Miller's Air Conditioning & Heating we take pride in being a high-quality HVAC Company serving the Tri-Valley area. We have been Livermore’s #1 choice for HVAC repair and service since 1960, so you can trust that we know how to get the job done right the first time. We’re a family-owned business that puts each of our customers needs ahead of our own, so if you need comprehensive furnace; air conditioning, or general HVAC services, give us a call at (925) 583-6387 today and we’ll take care of the job!
This review is for Ali, the service mechanic who responded to a service request at our home last week. We found Ali to be courteous, knowledgeable, and competent. This was not the first time Ali has been assigned to a serice call for us, and we are always pleased when he arrives. Ali not only takes the time to answer our questions, but often suggests ways to Increase the efficiency of our HVAC systems. He certainly represents Airtron well!!!

The HVAC industry is a worldwide enterprise, with roles including operation and maintenance, system design and construction, equipment manufacturing and sales, and in education and research. The HVAC industry was historically regulated by the manufacturers of HVAC equipment, but regulating and standards organizations such as HARDI, ASHRAE, SMACNA, ACCA, Uniform Mechanical Code, International Mechanical Code, and AMCA have been established to support the industry and encourage high standards and achievement.
For starters, once a year, vacuum out the area around the furnace’s blower. If possible, also slide out the fan unit, clean each fan blade with a toothbrush, and then vacuum with a brush attachment on a vacuum cleaner. While you’re at it, look for oil ports on the motor, normally located near the motor shaft. If the motor has these, apply two to three drops of non-detergent motor oil into each port (you may have to remove a cover plate to do this). Though most contemporary motors don’t require lubrication, do lubricate motors with oil ports once a year. For more about maintenance, see Maintenance Checklist for Central Heating Systems.
Heaters are appliances whose purpose is to generate heat (i.e. warmth) for the building. This can be done via central heating. Such a system contains a boiler, furnace, or heat pump to heat water, steam, or air in a central location such as a furnace room in a home, or a mechanical room in a large building. The heat can be transferred by convection, conduction, or radiation.

HVAC equipment is estimated to last about 15 to 20 years. Yet over the years, parts go out and need to be repaired. Heat sensors, exchangers, and ducts can become worn out. Air conditioning motors may need repairing from time to time. For repairs to your heating and air conditioning systems, and even general maintenance, let HomeAdvisor help. Enter your zip code and let us connect you with prescreened HVAC repair services near you.
Maryville, TN Appliance Repair Brookfield, WI Appliance Repair Appliance Repair Santa Cruz, CA Appliance Repair Riverside Appliance Repair Naples, FL 1500 S Willow St Appliance Repairs Appliance Repair in La Crosse Appliance Repair in Laredo 200 Westgate Dr Appliance Repairs 6929 Williams Rd Appliance Repairs Appliance Repair in Chesapeake Appliance Repair in Springfield, OH Appliance Repair in Whittier Appliance Repair in Massena Appliance Repair in Duluth Appliance Repair in Richardson Appliance Repair in Saint Joseph

A number of other variables can influence your decision on whether to repair or replace your furnace, as well. In addition to cost and brand, consider the expected lifetime of your furnace. If it is more than 15 years old, it might make more sense to invest in a new unit even if it costs more than simply repairing the current problem. Long-term costs also play into the equation. For example, your new furnace may be more energy efficient than the current unit. Even though you will pay more for the actual installation, you might be able to make back your investment through lower energy bills. To make your decision, consult with a reliable professional on what to do. In inspecting your furnace, they will be able to make an informed recommendation that looks not just to the next year, but years into the future. That way, you can make the best possible decision for your home and budget long-term.
With the ice and snow in the Charlotte area this week be sure to look at your outdoor unit for ice or snow buildup, especially if you have a heat pump. You can carefully attempt to remove any frozen buildup by pouring warm water over the unit to melt the snow and ice. Do not use any sharp objects to pick or knock the ice off, this could cause severe damage to the unit

Heating, ventilation, and air conditioning (HVAC[1]) is the technology of indoor and vehicular environmental comfort. Its goal is to provide thermal comfort and acceptable indoor air quality. HVAC system design is a subdiscipline of mechanical engineering, based on the principles of thermodynamics, fluid mechanics and heat transfer. "Refrigeration" is sometimes added to the field's abbreviation, as HVAC&R or HVACR or "ventilation" is dropped, as in HACR (as in the designation of HACR-rated circuit breakers).
Furnaces and thermostats are not mix-and-match appliances. Using the wrong type of thermostat with a furnace will cause operating problems and can be dangerous. Although thermostats look similar, they are designed very differently. There are numerous types of heating systems and thermostat systems and they need to be coordinated for safe and proper operation. There are three types of thermostat systems used today: millivoltage, low voltage, and line voltage.​
×